SUPPORT

KOMODO FIRMWARE 1.4.0 RELEASE NOTES KOMODO Release Build 1.4.0 December 10, 2020 IMPORTANT Download the latest REDCINE-X PRO from https://www.red.com/downloads UPGRADE KOMODO FIRMWARE 1. Copy upgrade.bin to a /upgrade directory on the CFast card. 2. Power up the camera and insert a CFAST card into the KOMODO media slot. 3. Go to Menu > Maintenance > Upgrade and select OK. 4. The camera initiates a 2 stage upgrade process which will automatically restart the camera. 5. After the camera restarts to complete the upgrade process, select RESTART once it appears. 6. Go to Menu > Camera Status > Camera Info to verify the firmware version after the camera boots.> SIGNIFICANT CHANGES SINCE PREVIOUS BUILD Added Canon RF lens support (BETA) Added Angelbird ARRI AV Pro 256GB CFast card support Added Camera type and build number to RCP2 Added Ethernet Zeroconf (Local-Link IP address) support Fixed slow load of large R3D clip in Playback Fixed out of sync clip index in Playback playlist Fixed Factory Reset to delete camera presets Fixed USB tethering with iOS 14 Fixed KOMODO Link Adapter interfering with CFast card detection Fixed user calibration with genlock enabled Fixed incorrect Image Stabilization UI status on boot Fixed intermittent snowy SDI image Fixed 'Unapproved Battery' error message running with DC Fixed Web UI Multi Action Menu buttons (LUT, CDL, Preset) Fixed AF window size on format change Fixed intermittent reboot hang Fixed SDI ST-352 payload for all Color Space and Gamma settings AF Improvements OPERATIONAL NOTES RF Lens control ring and focus range switch not currently supported Warning message will occur with unapproved Media and Batteries Copyright (c) 2004-2020 RED.COM, LLC. All Rights Reserved.

smallhd_OS_3.6.5 Bugs Fixed Fixed Support For WB on Mini LF (Cine 7 Camera Control).

RED Firmware 7.4.1 RELEASE NOTES DSMC2 Release Build V7.4.1 October 19, 2020 NOTE: Download the latest versions of REDCINE-X PRO and the RED ROCKET Installer or the RED ROCKET-X Installer from red.com/downloads. IMPORTANT: You cannot downgrade the camera to earlier than v7.0.2 after upgrading to v7.4.0. You must upgrade your REDMOTE firmware to v9.7.x. Download the firmware upgrade from red.com/downloads. Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions. Refer to https://support.red.com/hc/en-us/articles/225544547 for supported Canon lenses. Refer to https://support.red.com/hc/en-us/articles/225724728 for supported Nikon lenses. Refer to https://support.red.com/hc/en-us/articles/225565627 for supported PL lenses. Preset files created only on v4.0.x or later are compatible with v7.4.0. User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later. It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green. UPGRADE DSMC2 FIRMWARE TO V7.4.0 1. Connect a RED MINI-MAG to your computer. 2. Download the most recent firmware from www.red.com/downloads. 3. Unzip the firmware zip file. 4. Copy the force_upgrade folder and its contents to the top level of the SSD directory. 5. Eject or unmount the SSD, and then remove the SSD. 6. Ensure the camera is powered down. 7. Insert the SSD with the force_upgrade folder into your camera. 8. Power up the camera.The upgrade automatically runs at power up. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade. 9. After the camera powers down, remove the SSD and wait 10 seconds. 10. Power up the camera.The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors. 11. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded. 12. Reformat the SSD before recording to it. SIGNIFICANT CHANGES SINCE PREVIOUS BUILD V7.3.0 Added 1.8x ANA support for MONSTRO 8K VV Added Zeiss/Fujinon shading commands support Fixed intermittent media mounting issue Fixed missing external metadata in R3D with no lens mount installed Changed camera position character range to A-Z Changed Output Tone Map default to Medium Contrast Improved IPP2 to allow for LUTs with built-in output transforms Improved color reproduction of daylight light sources OPERATIONAL NOTES SPECIFIC TO BUILD V7.4.0 Perform sensor calibration after upgrade. Refer to https://support.red.com/hc/en-us/sections/204939547 for the list of Known Issues. Secure Format media before using Pre-Record. The horizon feature requires Gyro calibration be completed prior to use. Do not 3D sync when GEN ICON is not illuminated or yellow. Image Magnify is available during preview only. HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats. Copyright (c) 2004-2020 RED.COM, LLC. All Rights Reserved.